Pengecekan PE VPN (Cisco)
1. PE-D2-FR-VPN#sho run int gi0/0/1/6.3866 --> Melihat configurasi interface
2. PE-D2-FR-VPN#sho arp vrf nama_vrf gi0/0/1/6.3866 --> Cek status ARP (address resolution protocol)
3. PE-D2-FR-VPN#ping vrf nama_vrf 10.1.1.2 size 1000 r 50 source 10.1.253.4 --> ping menggunakan beban, repeat dan source ip
4. PE-D2-FR-VPN# traceroute vrf nama_vrf 10.1.1.2 source 10.1.253.49 --> tracert menggunakan source ip di int pelanggan.
5. PE-D2-FR-VPN# sh ip ro vrf nama_vrf | in 0/0/1/6.3866 --> cek statik routing ip yang di advertise
6. PE-D2-FR-VPN# sho bgp vrf nama_vrf summ | in ip ce --> cek routing bgp
Pengecekan PE Astinet / Transit (Huawei)
1. PE2-D2-FR-TRANSIT# display curr interface Gi4/0/9.37 --> Cek interface pelanggan
2. PE2-D2-FR-TRANSIT# display arp interface Gi4/0/9.37 --> Cek ARP arah CE
3. PE2-D2-FR-TRANSIT# display ip routing-table vpn-instance Astinet_Mix 36.x.x.x --> Cari interface berdasarkan IP Public
4. PE2-D2-FR-TRANSIT# ping -c 10 -s 1000 -a 36.92.222.100 -vpn-instance Astinet_Mix 8.8.8.8 --> Ping -c untuk count atau perulangan, -s untuk size atau beban, -a untuk source ip.
5. PE2-D2-FR-TRANSIT# tracer -a 36.92.222.100 -vpn-instance Astinet_Mix 8.8.8.8 --> untuk tracert ip ke backhaul dari pe cabang, atau tracert ke internet via ip di interface.
6. PE2-D2-FR-TRANSIT# disp bgp vpnv4 vpn-instance Astinet_Global routing-table (IP_CE) --> Cek BGP Astinet Global
7. PE2-D2-FR-TRANSIT# disp bgp vpnv4 vpn-instance Astinet_Domestik peer (IP_CE) verbose --> cek BGP Astinet Domestik
8.PE2-D2-FR-TRANSIT# display curr configuration | include 192.168.74.174 --> cek ip prefix
9. PE2-D2-FR-TRANSIT# display ip ip-prefix FROM-ASTINET-GRAND-INDONESIA --> cek prefix ip public
3. Pengecekan Metro Alcatel (NOKIA)
1. show service sap-using | match 5/1/59:3515 --> Cek cari vcid berdasarkan interface trunk dari PE dan vlan
2. show service id 650789 base --> Pengecekan VCID pelanggan
3. Pengecekan service type metro Epipe untuk point to point (PTP), dan VPLS untuk point to multipoint (PTMP)
4. Cek Bandwidth di metro bisa menggunan show service sap-using | match 5/1/59:3515
hasil jika, setelah vcid ingress / egress ber isi kode di awali
11 untuk satuan bandwidth kbps
12 untuk satuan bandwidth mbps
13 untuk satuan bandwidth gbps
14 untuk service corporate VVIP
1 di loss atau tanpa qos
contoh 12100 --> 100 Mbps, 11512 512Kbps
5. Pengecekan SAP dan SDP
SAP (Service Akses Point) SDP (Service Distribution Point)
di Metro 1 setelah PE, SAP menuju ke arah PE dan SDP menuju Metro ke 2 / metro lawan
di Metro 2 SAP port menujut lastmile GPON / Switch, sedangkan SDP menuju metro 1.
Pengecekan Metro Huawei
1. display curr interface Gi8/1/16.3624 --> Pengecekan Interface Pelanggan, mencari vcid dan ip metro lawan
2. ssh user@172.16.16.1 --> untuk masuk metro ke 2 di dapatkan dari perintah pertama.
3. display mpls l2vc 1969003624 --> Command di metro ke 2, untuk mencari interface arah lastmile.
4. display curr interface Eth-Trunk17 --> mencari ip lastmile interface tanpa vlan
Pengecekan GPON ZTE
1. telnet ip gpon via tacac akses --> untuk masuk ke GPON
2. show vlan (vlan id) --> cek interface by vlan
3. show gpon onu state gpon-olt_1/14/8:11 --> Cek status modem working / loss / offline
4. show gpon onu detail-info gpon-onu_1/14/8:11 --> Cek profile layanan lengkap dan log modem.
5. show mac vlan (vlan id) --> Cek mac address by vlan
6. show pon power attenuation gpon-onu_1/14/8:11 --> Cek redaman ont
7. sh running-config interface gpon-onu_1/14/8:11 --> Cek configurasi bandwidth di gpon
8. show onu running config gpon-onu_1/14/8:11 --> Cek vlan di tag di port lan berapa
9. show gpon remote-onu interface eth gpon-onu_1/14/8:11 --> Cek status LAN yg aktif / tercolok.
GPON#show vlan 3372
port(untagged):
port(tagged):
vport-1/4/1.3:4
xgei-1/19/1
sg1
GPON#show gpon onu state gpon_olt-1/4/1 3
OnuIndex Admin state OMCC state Phase state Speed mode
---------------------------------------------------------------
1/4/1:3 enable disable LOS GPON
ONU Number: 0/1
GPON08#show gpon onu detail-info gpon_onu-1/4/1:3
ONU interface: gpon_onu-1/4/1:3
Name: ********
Splitter:
Type: ZTEG-F609
Configured speed mode:GPON
Current speed mode: GPON
Admin state: enable
Phase state: LOS
Config state: success
Authentication mode: sn
SN Bind: enable with SN check
Serial number: ZTEGC85A42DA
Password:
Description: ********
Vport mode: gemport
DBA Mode: Hybrid
ONU Status: enable
OMCI BW Profile: 704kbps
OMCC Encrypt: disable
Line Profile: N/A
Service Profile: N/A
ONU Distance: 4947m
Online Duration: 0h 0m 0s
FEC: disable
FEC actual mode: disable
1PPS+ToD: disable
Auto replace: disable
Multicast encryption: disable
Multicast encryption current state:N/A
------------------------------------------
Authpass Time OfflineTime Cause
1 2025-05-14 14:09:31 2025-05-14 14:15:32 LOSi
2 2025-05-14 14:16:19 2025-05-15 18:16:17 DyingGasp
3 2025-05-15 18:17:02 2025-05-18 18:42:31 DyingGasp
4 2025-05-18 18:46:18 2025-05-25 03:13:52 LOSi
5 2025-05-25 16:08:47 2025-05-25 17:09:42 LOSi
6 2025-05-26 09:22:28 2025-05-29 18:48:11 DyingGasp
7 2025-05-29 18:48:55 2025-06-05 17:57:39 DyingGasp
8 2025-06-08 12:42:57 2025-06-08 12:43:19 LOSi
9 2025-06-08 12:43:47 2025-06-08 12:51:17 LOSi
10 2025-06-08 12:52:39 2025-07-08 19:14:25 LOSi
GPON08-D2-KDY-3#show running-config-interface gpon_onu-1/4/1:3
!<if-intf>
interface gpon_onu-1/4/1:3
$
!</if-intf>
!<xpon>
interface gpon_onu-1/4/1:3
tcont 1 name VOIP profile UP-564KF5
tcont 4 name ASTINET profile UP-10M
gemport 1 name VOIP tcont 1
gemport 4 name ASTINET tcont 4
$
pon-onu-mng gpon_onu-1/4/1:3
service ASTINET gemport 4 vlan 3372
service VOIP gemport 1 vlan 503
vlan port eth_0/1 mode tag vlan 3372
voip protocol sip
voip-ip ipv4 mode dhcp vlan-profile batchVlan503 host 2
sip-service pots_0/1 profile sipprofile userid +62215826660 username +62215826660@telkom.net.id password ******** media-prof
ile mediaprofile
sip-service pots_0/2 profile sipprofile userid +62215812539 username +62215812539@telkom.net.id password ******** media-prof
ile mediaprofile
veip 1 port udp 8080 ipv4 host 2
tr069-mgmt 1 acs http://acs.telkom.net:9090/web/tr069 validate basic username CPE password CPE
$
!</xpon>
Pengecekan GPON HUAWEI
1.
GPON00-D1-NGS-2>enable
2.
GPON00-D1-NGS-2#display vlan 3044 à Pengecekan Vlan
3.
GPON00-D1-NGS-2#display mac-address
vlan 3044 à Cek Mac address
4.
GPON00-D1-NGS-2#display ont info 0 5 5
27 à Cek
Detail Info Gpon
5.
GPON00-D1-NGS-2#display
current-configuration ont 0/5/5 27 à cek tag vlan di port gpon
6.
GPON00-D1-NGS-2(config-if-gpon-0/5)#display
ont port state 5 27 eth-port all à
CEK PORT LAN yang AKTIF DI ONT
7. GPON00-D1-NGS-2(config-if-gpon-0/5)#display ont optical-info 5 27 >> CEK REDAMAN à Cek Redaman
1. GPON01-FER# cd onu (ambil dari dir)
2. GPON01-FER\onu# show onu service by svlan 3777 --> Cek VLAN
3. GPON01-FER\onu# show mac_list slot 8 pon 4 onu 10 port 1 --> Cek Mac Address
4. GPON01-FER\onu# show mac-address vlan 3359 --> Show Mac Adrress
5. GPON01-FER\onu# show onu optical-info slot x pon x onu x --> Cek Redaman
6. GPON01-FER\onu# show onu_state slot 8 pon 5 --> cek status semua onu yg aktif
7. GPON01-FER\onu# show onu service-info slot 11 pon 7 onu 11 --> cek configan di port brp
8. GPON01-FER\onu# show onu state-info slot 8 pon 4 onu 10 --> Cek Log
9. GPON01-FER\onu# show onu_time slot 8 pon 4 onu 10 --> cek modem sudah hidup berapa lama
10. GPON01-FER\onu# show onu_state slot 6 pon 5 onu 1 --> cek status modem saat ini
11. GPON01-FER\onu# show onu slot 4 pon 6 onulist all --> cek semua status modem 1 onu
11. GPON01-FER\onu# show service_vlan all --> cek all service yg ada di gpon
12. GPON01-FER\onu# show running-config slot 4 pon 6 onu 10 --> Cek SN Modem
13. GPON01-FER\onu# show onu_wan_service slot 13 pon 13 onu 3 --> Lihat configurasi WAN, PPPOE
1. GPON01-FER# >environment#show vlan residential-bridge summary 3516 --> cek vlan summary
2. GPON01-FER# show interface port ont:1/1/4/1/32
3. GPON01-FER#show vlan cross-connect 3609 --> Cek Port
4. GPON01-FER>#info configure equipment ont interface 1/1/2/5/66 --> Cek SN
5. GPON01-FER>#show equipment ont operational-data 1/1/1/2/14 --> Cek Status Modem
6. GPON01-FER>#show equipment ont optics 1/1/1/2/14 --> Cek Redaman
Pengecekan Switch Fiberhome
1. PE-D2-FR-MGT# telnet 172.254.16.178 /vrf VRF-SS-OAM --> Masuk sw via ip managment, vrf menyesuaikan yang digunakan.
2. SW-D2-FERRY# show vlan (vlan id) verbose | show vlan property --> cek vlan layanan
3. SW-D2-FERRY# show mac-dynamic vlan 2582 --> cek mac address by vlan
*command di atas bisa di tipe sw Fiberhome Fengine S5800 versi software V210R240, Di tipet FH S4800 software V210R220 tidak bisa.
4. SW-D2-FERRY# show running-config --> Cek configurasi keseluruhan
5. SW-D2-FERRY# show interface --> Cek interface secara keseluruhan
6. SW-D2-FERRY# sho interface gigaethernet 1/1 config --> Cek config interface summary
Pengecekan Switch Cisco WS-C3560-48TS
1. PE-D2-FR-MGT# telnet 172.254.16.178 /vrf VRF-SS-OAM --> Masuk sw via ip managment, vrf menyesuaikan yang digunakan.
2. SW-D2-CISCO# sho vlan id 1000 --> Cek Vlan layanan
3. SW-D2-CISCO# show mac-address-table --> Cek mac address keseluruhan
4. SW-D2-CISCO# show mac-address-table dynamic vlan 996 --> Cek mac address by vlan
5. SW-D2-CISCO# show running-config --> cek configurasi secara kesuluruhan
6. SW-D2-CISCO# sho runn int Gi 1/1 --> Cek interface Gi 1/1
Pengecekan Switch HP A5120-24G-PoE+
1. PE-D2-FR-MGT# telnet 172.254.16.178 /vrf VRF-SS-OAM --> Masuk sw via ip managment, vrf menyesuaikan yang digunakan.
2. SW-D2-HP# display vlan 21 --> Cek Vlan layanan
3. SW-D2-HP# display mac-address vlan 21 --> Cek mac addresss vlan 21
4. SW-D2-HP# display curr interface --> Cek konfigurasi secara keseluruhan
5. SW-D2-HP# display curr interface gi1/0/6 --> Cek konfigurasi int Gi1/0/6
Boleh di share kembali, mohon di cantumkan sumber www.ferrysetiawan.com
PDF Bisa di download di Disini
Mau belajar bareng terkait jaringan bisa join di group telegram https://t.me/belajarjaringanBJB
1 komentar:
mantabbbb
Posting Komentar